Some users experience a subtle tingle or sensation of warmth from the Senergy BioTransducer CrystalWave® Pro. Most people don’t feel any sensations when using the Senergy BioTransducer CrystalWave® Pro. You may feel initial apprehension about providing therapy to yourself or others. When you carefully follow the instructions and directions, there’s no need to be concerned. The devices and therapy steps were created with the knowledge that application will be general and does not have to be precisely aligned with any given point of the body. Even if you are providing the therapy to a different area than intended, it is not harmful and, in most cases, will still benefit you.

Setting Up Your Senergy BioTransducer CrystalWave® Pro

Connect the USB cord to your Senergy BioTransducer CrystalWave® Pro and the A/C adaptor to charge

• It takes 6 hours to charge to full capacity and therefore should be charged overnight.

• One charge lasts 3 days, depending on use

• It is best to treat it like a cell phone, don’t run the battery completely down

PLEASE NOTE: Prior to using your Senergy BioTransducer CrystalWave® Pro for therapy, you must balance the polarity of your body. Refer to the Daily Practice Guide for instructions on balancing polarity.

Read & download the full PDF on the Daily Practice here.

INSTRUCTIONS FOR USE

1. Connect the Senergy BioTransducer CrystalWave® Pro to the Tennant BioModulator® with the connection wire. Use care when plugging the wire into the port on the BioModulator®. You can cause damage to your BioModulator® if it is knocked or bumped when plugged in. It is very important to remove the plug when not in use.

2. Turn on your BioModulator® (Pro or Plus).

3. Set the mode.

For BioModulator® Plus:

• TEN-8 for pain and inflammation related to muscle, bone, ligament and tendons. 

• INFINITY for all other issues related to organs and general health. 

• INFINITY for eye treatment.

For BioModulator® Pro:

• TEN-8 for pain and inflammation related to muscle, bone, ligament and tendons. 

• INFINITY for all other issues related to organs and general health. 

• VA-STEP for eye treatment. 

4. Adjust the power by pressing the + and – buttons. Since there is no skin contact you may increase the power as high as you want when using it on the body. When using it on the eyes set the power as is indicated in the eye treatment section (pg 7). 

5. Point the Senergy BioTransducer CrystalWave® Pro at the area of concern, holding it between 1⁄2 an inch to 3 inches away from the body. (Please note: If you rest the rubber cap against the skin, you may have an allergic reaction to the rubber.) 

6. As a general guideline, therapy times are flexible just as they are when using the BioModulator® alone. 

For example:

a) 5 – 15 minutes for minor issues and for general use. 

b) As long as needed for more serious conditions. 

Tip: Therapy can continue for several hours when you mount the Senergy BioTransducer CrystalWave® Pro to a mic stand and position it on the area of concern. See pg. 9 of the Quick Start Guide for caring for your batteries when doing longer therapy sessions. 

If you are familiar with our Senergy BioTransducer CrystalWave® III, you know that it is powered solely from the BioModulator®. The Senergy BioTransducer CrystalWave® Pro is much stronger, therefore requires the additional power from the internal lithium battery. Be sure both the Senergy BioTransducer CrystalWave® Pro power and the BioModulator® are turned on when you are doing treatments. 

NOTE: You must have a BioModulator® device to complete this daily practice.

This daily practice will help balance and prepare your body so it can properly receive and use the voltage provided by your BioModulator® device for healing.

Click Here to read & download the full PDF on the Daily Practice

You can download this detailed instructional guide on how to care for and use your Senergy BioTransducer CrystalWave® Pro to its fullest potential.

Click Here for the Senergy BioTransducer CrystalWave® Pro QUICK START GUIDE.